weeloha.blogg.se

1. #Hauppauge wintv dual hd usb dual tuner install#
2. #Hauppauge wintv dual hd usb dual tuner drivers#
3. #Hauppauge wintv dual hd usb dual tuner driver#
4. #Hauppauge wintv dual hd usb dual tuner software#
5. #Hauppauge wintv dual hd usb dual tuner tv#

tveeprom: audio processor is None (idx 0)

#Hauppauge wintv dual hd usb dual tuner tv#

tveeprom: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc) Sample Kernel Output (both tuners Linux 4.17-rc1, Model 01590, USB device ID 2040:0265) tveeprom: tuner model is SiLabs Si2157 (idx 186, type 4) em28xx: Registered (Em28xx dvb Extension) extension em28174 #0: DVB extension successfully initialized usb 1-1: DVB: registering adapter 0 frontend 0 (Silicon Labs Si2168). DVB: registering new adapter (em28174 #0) si2168 11-0064: Silicon Labs Si2168 successfully attached i2c i2c-11: Added multiplexed i2c bus 12

#Hauppauge wintv dual hd usb dual tuner driver#

usbcore: registered new interface driver em28xx tveeprom 11-0050: has no radio, has IR receiver, has no IR transmitter tveeprom 11-0050: audio processor is None (idx 0) tveeprom 11-0050: TV standards PAL(B/G) NTSC(M) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xfc) tveeprom 11-0050: tuner model is SiLabs Si2157 (idx 186, type 4) em28174 #0: Identified as Hauppauge WinTV-dualHD DVB (card=99) em28174 #0: microcode start address = 0x0004, boot configuration = 0x01 em28xx: New device HCW dualHD 480 Mbps (2040:0265, interface 0, class 0) usb 1-1: New USB device strings: Mfr=3, Product=1, SerialNumber=2 usb 1-1: New USB device found, idVendor=2040, idProduct=0265 Sample Kernel Output (first tuner only) usb 1-1: new high-speed USB device number 6 using xhci_hcd After changing the mode to "bulk" using this tool, please check the dmesg messages again and verify that it now states "dvb set to bulk mode".

#Hauppauge wintv dual hd usb dual tuner install#

The only way to change it is to use a free windows tool provided by the manufacturer Hauppauge: Please install the windows driver for the stick first, because they need to be installed before running the tool. Currently there is no known way to change that mode using a linux command or passing options to the kernel module. When the stick is detected there is a line that reads "dvb set to isoc mode" when in isochronous mode, when bulk mode is active, an analogous message is shown. You can check the mode your stick is using with dmesg.

#Hauppauge wintv dual hd usb dual tuner software#

This problem has been confirmed by many users of the VDR (German language, ), but is very likely to occurr with other software as well. when a EPG scan is running in the background). This often leads to artifacts being shown in the video stream when both tuners are active (e.g. The stick supports two transfer modes: isochronous and bulk, whereas most revisions use the isochronous mode by default. Only the first tuner on Model 01595 device is supported since Kernel 4.11 (see commit ).īoth tuners on Model 01590 device and Model 01595 device are supported since Kernel 4.17 (see commit ). Only the first tuner on Model 01590 device is supported since Kernel 4.7 (see commit ).

#Hauppauge wintv dual hd usb dual tuner drivers#

The Model 01590 demodulator needs a firmware which can be found for example at Drivers The following part refers specifically to Model 01590 or Model 01595. Identification sudo lsusb -v -d 2040:026dīus 001 Device 006: ID 2040:026d HauppaugeīDeviceClass 0 (Defined at Interface level)īInterfaceClass 255 Vendor Specific Classĭevice Qualifier (for other device speed): This version of the board is like a USB version of the Hauppauge WinTV-HVR-2255 PCIe card. Model 01595 (USB device ID 2040:026d) Components Used

2.4 Sample Kernel Output (first tuner only).